When the air conditioning stops keeping up on a hot afternoon, or the furnace quits on a cold night, the first question is usually the same: how quickly can somebody get out here, and what is this going to cost. Those are fair questions, and they deserve a straight answer on the phone rather than a vague window and a callback that never comes. Heating and cooling calls across Manor and Travis County are handled here, from straightforward repairs to full system replacements, and the price gets confirmed before anything is scheduled.
We cover Manor for the full range of residential and commercial HVAC work. Whether it is a homeowner dealing with a system that has not been serviced in years, a landlord managing a rental that lost cooling, or a business that cannot afford to have the building uncomfortable for its customers, the call works the same way: scope the job on the phone, confirm the price, then get it on the schedule. We are available every day from 5:30 AM to 9:00 PM.
Some spaces were never connected to the central system in the first place. A converted garage, a room addition built after the original ducting was run, a detached office, a workshop that doubles as a workspace year-round. Central ductwork cannot always be extended to reach those spaces without a major renovation, and in some cases the existing system is not sized to carry the extra load anyway.
A ductless mini-split handles those situations without touching the existing system. The indoor unit mounts on the wall, the outdoor unit sits nearby, and the two connect through a small penetration in the wall. There is no ductwork to run and no return air to balance. The system conditions the space independently, which also means the temperature in that room can be set without affecting the rest of the house.
Ductless systems are not limited to a single room. A multi-zone mini-split connects several indoor units to one outdoor unit, which makes them practical for a small commercial building, a rental property where different tenants want different temperatures, or a home where the existing central system leaves some rooms consistently uncomfortable. Each zone runs independently. If one room needs cooling and another does not, only that room's unit runs.
Mini-splits that are already installed need the same attention as any other system. When a ductless unit stops cooling or heating as it should, the diagnostic process is the same: identify the fault, explain what it involves, confirm the repair cost before any work begins. Common faults include refrigerant issues, sensor failures, and drainage problems that cause the unit to shut itself off.
Call (737) 353-9556 and we will go through what the system is doing on the phone.
The more detail you can share when you call, the better we can scope the job before the visit. You do not need to know the technical cause. What matters is what the system is doing: running but not cooling, not turning on at all, making a noise it was not making before, keeping some rooms comfortable while others stay too warm or too cold.
It also helps to know the equipment involved. The make and model of the outdoor unit, the age of the system if you have it, and whether the problem came on suddenly or has been getting worse over time. If there is a thermostat error code showing, write it down before you call. None of that is required, but each detail narrows the scope on the phone and means the visit can be set up accurately from the start.
We confirm the diagnostic rate before the visit is scheduled. For replacement or installation work, the price is confirmed once the system is scoped, so you know the number before committing to anything.
Call (737) 353-9556 and we will work through the details.
A quote given before a system is looked at is a guess, and a guess is not a price. What actually moves the cost of a repair is what the fault turns out to be, where it is in the system, and whether parts need to be sourced. A capacitor replacement and a compressor replacement are not the same job, and neither is a refrigerant recharge and a coil repair.
For replacement work, the price depends on the equipment selected and what the installation involves. A straightforward swap of an existing system for a same-configuration replacement is a different scope than a conversion from a furnace-and-AC setup to a heat pump, or a first-time installation where new line sets and electrical connections are required. The electrician owns the panel and the circuit. We own the equipment and the installation.
The repair-versus-replace question comes up on a lot of calls, and it is worth answering honestly. When a system is aging and the repair cost is approaching the value of what is left in the equipment, the numbers usually favor replacement. When the fault is straightforward and the system has useful life remaining, repair is the right answer. We will say which one applies and explain why, before anything is scheduled.
A system that heats or cools well in some rooms and poorly in others is not always a failing system. Sometimes the issue is airflow distribution. Registers that are partially closed, supply and return imbalances, or ductwork that was never balanced correctly after a renovation can all produce uneven comfort without any fault in the equipment itself. Rebalancing the system means measuring what is actually moving through each zone and adjusting the distribution to match what the space needs.
A heat pump that blows cool air in heating mode, or one that ices up and stops performing, often has a defrost or reversing valve fault rather than a compressor problem. The diagnostic matters here because the symptoms of a defrost fault and a refrigerant issue can look similar from the outside. The technician who comes out checks the defrost cycle, the reversing valve operation, and refrigerant charge in sequence, and explains what was found before recommending a repair.
An AC that runs continuously without dropping the indoor temperature is one of the more common calls in a humid regional climate. The causes range from a low refrigerant charge to a dirty evaporator coil that has lost its ability to transfer heat, to an oversized or undersized system that was never the right fit for the space. Evaporator coil cleaning and repair address one of the most common efficiency losses. Comfort problems get diagnosed rather than guessed at. The visit covers a full assessment of why the system is running without satisfying, not just a check of the most obvious component.
A system that never shuts off is doing one of two things: working against a load it cannot handle, or compensating for a loss somewhere in the system. Leaking ductwork, a failing compressor, a refrigerant issue, or a thermostat that is not reading correctly can all produce the same symptom. An energy-efficiency upgrade, whether that means sealing the duct system, replacing a failing component, or installing a smart thermostat that gives the system better control, can bring the runtime back to where it belongs. We look at the whole system rather than the single component that seems most likely.
When you call, the visit is scoped on the phone. You describe what the system is doing, we ask the right questions, and the diagnostic rate is confirmed before anything is scheduled. For urgent calls, where there is no cooling in the building or no heat in the house, we take those every day from 5:30 AM to 9:00 PM and move them as quickly as the schedule allows.
When the property has a tenant in it, or a business that cannot close for the day, we work around what the space needs. Access arrangements, any preparation the occupant needs to make, and what the visit will involve are all covered on the call before the technician comes out. We keep you informed from diagnosis to final test.
Not every call is a repair. A seasonal tune-up before the long cooling season, or a pre-winter check of the heating system, catches the problems that become expensive repairs when they are ignored. A standard maintenance visit covers coil condition, refrigerant level, blower performance, thermostat calibration, and an overall system check. Code-compliant HVAC work on every visit means the equipment is left in a state that meets the standards the area enforces. Homeowners in Manor often read our services page for heating and cooling work before getting in touch.
We serve Manor and the communities around it throughout Travis County. If you are in Pflugerville, Hornsby Bend, Wells Branch, Webberville, or Elgin, the call works the same way and the same schedule applies.
Coverage in Travis County runs to both residential and commercial properties. A homeowner in Manor, a landlord managing a rental in Pflugerville, and a business in Wells Branch all reach the same line and get the same process: scope the job, confirm the price, schedule the visit.
Call (737) 353-9556 to get a quote for any heating or cooling work in the area. We are available every day from 5:30 AM to 9:00 PM.
No airflow with the system appearing to run usually points to a blower motor or blower wheel failure, a seized motor, or a control board fault that is running the compressor without energizing the blower. A completely blocked filter can also cause the system to shut the blower down on a safety limit while the rest of the system continues to cycle. The technician will check the blower circuit and the safety controls to identify the cause.
Yes. We cover Manor and the surrounding communities in Travis County, including Pflugerville, Hornsby Bend, Wells Branch, Webberville, and Elgin. The call works the same way regardless of which community you are in: scope the job on the phone, confirm the price, then schedule.
Call (737) 353-9556 and we will confirm coverage for your address.
A second opinion is always reasonable, and we will not pressure you otherwise. If you have a quote from another company and want to understand what it covers, call us and we will go through the scope and pricing for your situation. A replacement is a significant investment, and you should feel confident in the decision before committing.
Someone needs to provide access to the equipment, but that does not have to be the owner. A tenant, a property manager, or anyone authorized to allow access can be present. The key requirement is that access to both the indoor and outdoor equipment is available for the duration of the visit. If access is through a lockbox or a key drop, that is confirmed on the call before the visit is scheduled.
Coverage is based on the address, not on which side of a town boundary it sits.
Call (737) 353-9556 with your address and we will confirm whether it falls within the area we serve and what the schedule looks like.
Boundary locations are handled the same way as any other address in the coverage area.
Yes. Managing agents and property management companies call us regularly to book service and repair visits for properties they oversee. On the call, let us know you are booking on behalf of the owner and we will confirm access arrangements, pricing, and what the visit covers. The process works the same way regardless of who makes the booking.
In a town this size, a lot of the housing stock has systems that have been running for years without a formal tune-up, and the most common calls reflect that: refrigerant that has dropped below the correct charge, evaporator coils that have accumulated enough buildup to reduce heat transfer, and ductwork that was never balanced after a room addition or renovation. Thermostat and smart-control installation also comes up regularly when an older control is no longer compatible with a newer system. If the system has been running but not quite right for a season or two, that is worth a diagnostic call.
Some systems run for years in a state that is never quite right. The house is too warm by afternoon, the heating never fully satisfies, the energy bills climb without an obvious reason. That is not a system working as it should, and it does not resolve on its own.
Call (737) 353-9556.
We will go through what the system is doing, confirm what the visit covers and what it costs, and get it on the schedule. We are available every day from 5:30 AM to 9:00 PM.
HVAC service nearby: Pflugerville, Hornsby Bend, Wells Branch, Elgin, Hutto.
Below is a quick look at the heating and cooling work we handle for homes and businesses in Manor and across Travis County. Each service is scoped on the call before anything is scheduled, and the price is confirmed before any work begins. If you have a question about a specific service or situation, call us and we will walk through the details with you.
| Service | What It Covers | Best Suited For | Helpful Details |
|---|---|---|---|
| Thermostat & Smart-Control Installation | Compatibility check with existing equipmentThermostat removal and installationProgramming and scheduling setupCalibration to the system | Homeowners upgrading from a basic thermostat or replacing a control that is not reading or responding correctly | Heat pumps and multi-stage systems have specific wiring requirements that affect which smart thermostats will work, so compatibility is confirmed on the call before scheduling |
| AC Repair & Service | Fault diagnosis and repairRefrigerant level checkAirflow and coil inspectionComponent testing | Any home or building where the AC is not cooling, running constantly, or making unusual noises | Central Texas summers put heavy demand on cooling equipment, so catching a fault early keeps a repair from turning into a replacement |
| Full System Installation & Replacement | Load calculation for the spaceEquipment selection and sizingFull system installationPerformance test before sign-off | Homes and commercial properties where the existing system has reached the end of its useful life or repair costs no longer make sense | Correct sizing matters more than brand in Central Texas, where an undersized unit will run constantly through a long summer and wear out faster |
Every job in Manor and Travis County starts the same way: a call where we scope the work, confirm the price, and answer your questions before anything is scheduled. Call (737) 353-9556 and we will get you the details you need.
(737) 353-9556